Go Faster Redneck Parts!!

[drop top]

YEEEEEEE HAAAW!

Step 1- Diablo Predator in hand

Step 2- Metco 4lb Pulley Kit ordered today from AVF

Step 3- Sit in chair and make vroom vroom noises til spring!!!


:trucker::trucker::trucker::trucker::trucker:

[TF2v97SN]

so whos gona install ur pulleys?

[F8LBITE]

Yeah, when's the party?

[HELLFYR]

Why? Not hard to do.
Cobra was a little challenging with the introduction of a new mounting plane / bracket for the pulley due to removal of the stock pulley cage, but other than that it is just cranking on wrenches and cussing everytime you bust a knuckle open in the tight quarters in front of the block.

[F8LBITE]

Soooo you did yours by yourself on your garage floor then?

[HELLFYR]

Soooo you did yours by yourself on your garage floor then?

Essentially... with the help of a lift... and flying bodies to break the crank bolt loose.

D9 did offer moral support my snickering at me every once in awhile.

[TF2v97SN]

Essentially... with the help of a lift... and flying bodies to break the crank bolt loose.

D9 did offer moral support my snickering at me every once in awhile.

heck thats easy on a manual trans, put it in gear and pull the ebrake, try that on an auto and it doesnt work

[sonicx]

YEEEEEEE HAAAW!

Step 1- Diablo Predator in hand

Step 2- Metco 4lb Pulley Kit ordered today from AVF

Step 3- Sit in chair and make vroom vroom noises til spring!!!


:trucker::trucker::trucker::trucker::trucker:

What kind of power will she be putting down then?

[HELLFYR]

heck thats easy on a manual trans, put it in gear and pull the ebrake, try that on an auto and it doesnt work

Not as easy as you may think.
Took car in 6th gear, me with both feet on the brake, a 24" breaker bar with a 4 foot jack handle on the end of it to provide more leverage, PLUS
a run at it from the side by the D9-meister. Those are torqued WELL over 300ft-lb

[TF2v97SN]

Not as easy as you may think.
Took car in 6th gear, me with both feet on the brake, a 24" breaker bar with a 4 foot jack handle on the end of it to provide more leverage, PLUS
a run at it from the side by the D9-meister. Those are torqued WELL over 300ft-lb

impact wrenches work great..... oh yea, D9 doesnt like those

[drop top]

Did anyone hear me tonight? I was making loud vroom vroom noises....

[DNeinstadt]

impact wrenches work great..... oh yea, D9 doesnt like those

I prefer removing by hand, and there's no room in there for an impact... do you usually remove the radiator/heat exchanger/condensor?

[p51mstg]

Oh... I thought that was the neighbor!




Did anyone hear me tonight? I was making loud vroom vroom noises....

[ShadowGT04]

Where did you order your pulley from? Im looking at maybe getting one for my Kenne Bell but dont know where they sell them

[TF2v97SN]

on a lightning, remove fan and use 3/8's impact, also

[DNeinstadt]

On a Cobra? :) And what enthusiast has a 3/4" impact????

[MadJack]

let me look, i might have a 3/4 impact... lol

[TF2v97SN]

i said 3/8ths not 3/4

[drop top]

on a lightning, remove fan and use 3/8's impact, also

Looks like I might have found a volunteer.
Well since you are so knowledgable and smart

[DNeinstadt]

LOL, reading comprehension fails me. :)

[TF2v97SN]

Looks like I might have found a volunteer.
Well since you are so knowledgable and smart

although last time i had to pull one off i had the tool to hold the flex plate, but i cant borrow the tool anymore

[pnkrckr]

Sounds like fun! Just got my Xcal 3 the other day!

What else do you have done?

-Chris

[drop top]

Shift Kit
JLT Cold Air
Metco 4lb Pulley
Bassani High Flow Cats
Bassani Stainless Cat Back
Diablo Predator Tuner
Nitto 555R's Drag Radials


The rest of the mods are all cosmetic-
Bed Rug
ARE Hard Shell Cover
Black Tails
Etc..

Should be good for around 400whp and 5-something rwtq

[MadJack]

you should lower it a bit....

[drop top]

you should lower it a bit....
:nuts:
NOPE!
:geeza:

[MadJack]

why not lol

[pnkrckr]

Shift Kit
JLT Cold Air
Metco 4lb Pulley
Bassani High Flow Cats
Bassani Stainless Cat Back
Diablo Predator Tuner
Nitto 555R's Drag Radials


The rest of the mods are all cosmetic-
Bed Rug
ARE Hard Shell Cover
Black Tails
Etc..

Should be good for around 400whp and 5-something rwtq

Nice! We will have similar mods when I'm done tinkering for the winter! Got a shift kit on the way in the next couple weeks here :headbang:

Bed Rug = awesome, got one too!

[MadJack]

i dont mean slam it, but maybe bring it down a inch.... it'd help handleing.

[No1Ford]

The rest of the mods are all cosmetic-
Bed Rug
ARE Hard Shell Cover


Added weight, that going to slow ya down.:mooner: